AFM Wood Finishes

	Title
	Polyureseal BP The highest quality water-based clear gloss finish available today. Its exceptional durability and abrasion resistance, coupled with high solids, very low odor, and very low VOC, make it the clear alternative to conventional solvent and water-based polyurethanes. Also available in satin. USE ON - Safecoat® Polyureseal BP can be used on unfinished (or properly prepared and sanded previously finished) wooden surfaces such as floors, furniture and cabinetry, and is excellent for gym floors and auditoriums APPLICATION - Always have adequate ventilation. Intermix (boxing) all containers of the same sheen to ensure gloss uniformity before applying. Before using, mix coating thoroughly by gently stirring or rolling container to avoid air bubbles. Be sure to stir product thoroughly every 20 minutes during application. Do not shake container. Pour material to be used into another container before applying coating to avoid contaminating main container. Then apply as is, using a quality nylon brush, pad applicator, or unheated spray applicator. Apply liberal coats, keeping a good wet edge and avoid overbrushing. In most cases, a minimum of 3 coats is required, depending on the surface. When spraying, use a .015 tip or smaller. Apply thin even coats when spraying rather than heavy coats which will tend to sag. If spray pattern begins to dryspray, reduce air pressure and increase material flow to surface. Use a damp, dust free rag after sanding to remove dust particles. Use aluminum oxide or silicon carbide sandpaper to sand between coats. For best results, this product should not be reduced. Use only during low or moderate humidity conditions. Applying this product over lightly dampened surfaces can assist the user in controlling the dry time. Smoother finishes are achieved when surfaces are damp during application. Note: these instructions are intended to be general only and not exhaustive. The applicator should determine which preparation and techniques are best suited to the specific surface. COVERAGE - One gallon of Safecoat Polyureseal BP covers approximately 350 square feet in one coat depending on method of application and surface porosity. DRYING/CURING TIME - Under normal conditions,Safecoat® Polyureseal BP dries to touch in one hour, is sandable after 2-4hours, and re-coatable after 4-8 hours. The product will continue to cure and become harder over time. Avoid traffic for at least 24 hours after application. Normal conditions include a dry surface, access to fresh airflow, moderate humidity, and temperatures around 70°F. Thick application, high humidity or conditions other than normal will cause Safecoat Polyureseal BP to dry and cure more slowly. SPEC SHEET $44.00 Sheen * AFM Product Size *
	Safecoat® Polyureseal EXT (Gloss or Satin) Safecoat Polyureseal EXT is a premium quality crystal clear acrylic urethane that provides a tough, durable surface for exterior use on walkways, pool decks, floors, patios and showrooms. Can also be applied to raw wood or wood stained with Safecoat wood stains, and concrete or previously painted surfaces that are properly prepared. Spec Sheet $36.00 AFM Product Size * Sheen *
	DuroTone - pint Safecoat DuroTone^TM is a fast curing low odor semi-transparent interior wood stain using no aromatic solvents, formaldehyde, UV inhibitors or Hazardous Air Pollutants. Available in Cognac, Walnut, Warm Cherry, Golden Oak, Honey Maple, Jacobean, Red Mahogany, Warm Oak, Nutmeg, Pecan, White Pickle and Clear. Available in pints or gallons. SPEC SHEET $14.00 DuroTone Color
	AFM Naturals Clear Penetrating Oil This organic plant-based premium penetrating oil for new and old unfinished woods is excellent on wood fencing, timberwork, furniture, decking, paneling and trim. It rejuvenates, weatherproofs and enhances the innate beauty of wood surfaces. Reduces peeling, blistering and cracking. Unlike products used for similar purposes, it’s benzene free. Non-flammable Interior or exterior SPEC SHEET $39.00 AFM Product Size *
	AFM Naturals Oil Wax Finish This organic plant-based premium hardener and sealer for unfinished woods works well on all ready-to-finish wood, bamboo and cork floors, and other interior wooden surfaces, including children’s furniture and toys. It contains a sophisticated combination of natural resins and waxes that together create a durable, water-repellant, watermark-resistant finish and sealer, enhancing and maintaining wood beauty and breathability. Based on natural vegetable oils, waxes and plant extractives, this product is free of lead, cobalt and citrus drying compounds. SPEC SHEET $44.00 AFM Product Size *
	Acrylacq Safecoat Acrylacq is a clear, high gloss, water based replacement for high solvent content lacquer. It is hard and durable with superior resistance to stains, marring and fingerprint marks. Also available in satin. SCS CERTIFIED - LEED QUALIFIED COVERAGE: One gallon of Safecoat Acrylacq covers approximately 350 square feet in one coat depending on method of application and surface porosity. Never apply more than two coats of Satin as it can begin to have a milky apprearence. For the best results start with gloss and top coat with the satin. **** We stock Matte & Glass. Satin will ship from manufacturer and take a few days longer. SPEC SHEET $40.00 AFM Product Size * Sheen *
	Water Shield This clear, versatile, controlled-penetration, water-repelling sealer provides an invisible barrier against water, and resists oils, grease and similar liquids. It is fast drying, has excellent adhesion and is easy to apply. Also helps to harden, dust-proof and control efflorescence in masonry surfaces. May be used on painted surfaces and may be painted over when dry. Dries clear and does not discolor. This is a great interior and exterior sealant Great for wood decks as well as stone cement and porouse tile. SPEC SHEET $63.00 AFM Product Size *
	SAFE SEAL OVERSTOCK SALE!!!!! Gallons Reg. $70. SALE! $52 Safecoat Safe Seal is a multi-use, waterbased, low gloss sealer for highly porous surfaces such as particle board, plywood, processed wood and porous concrete. Used primarily to reduce toxic outgassing: in particular, it is highly effective at sealing in formaldehyde outgassing from processed wood such as plywood, particle board and pressed wood. Safecoat Safe Seal is virtually odorless on application and odorless once cured. USE ON - Porous surfaces such as processed wood products, concrete, wood, new drywall, and plaster. Test surfaces first in inconspicuous areas to be sure product absorbs into surfaces completely. Excellent at controlling emissions of open faced and faced fiberglass batt insulation -simply fog spray surfaces. Safe Seal’s superior adhesion to a variety of surfaces allows for its use as a bonding primer to improve the adhesion and bonding power of adhesives and coatings on difficult surfaces. For example, apply a thin coat to the slab and bottom of the tile before laying floor tile adhesive (in this application no cure period is necessary; the adhesive may be applied while the Safe Seal is still tacky). APPLICATION - To assist in quick drying/curing, bring adequate ventilation and air flow to the work area. Before using, stir Safecoat® Safe Seal thoroughly but without excessive agitation so as to avoid air bubbles. Then apply as is, using a brush, roller, sponge or appropriate spray equipment. Apply in thin coats. For most jobs, reducing this product should not be necessary. Milky appearance, dries clear. As the flexible membrane created by Safe Seal remains slightly tacky even when cured, surfaces treated with Safe Seal should generally be coated with a finish coating. For best results, this product should not be reduced. Note: these instructions are intended to be general only and not exhaustive. The applicator should determine what preparation and techniques are best suited to the specific surface. COVERAGE - One gallon of Safecoat Safe Seal covers approximately 350 square feet in one coat depending on surface porosity. DRYING/CURING TIME - Under normal conditions, Safecoat® Safe Seal dries to touch in one hour or less and can be top-coated (or if the surface is still porous recoated with another coat of Safe Seal) after 2 hours. Normal conditions include a dry surface, access to fresh air flow, moderate humidity, and temperatures above 55°F. Thick application, high humidity or conditions other than normal will cause Safecoat SafeSeal to dry and cure more slowly. SPEC SHEEET $27.00 AFM Product Size *
	Hard Seal Safecoat Hard Seal is a multi-use, clear gloss sealer especially formulated to provide mar resistance to both low and high porosity surfaces. Because it forms a continuous membrane when applied properly it is particularly effective at sealing in any pollution or toxic chemical compounds outgassing from the surface to which it is applied. USE ON - Typically used on previously uncoated and unsealed woodwork, cabinetry and vinyl tile. To prevent outgassing of previously coated surfaces, can also be applied over existing paints, stain and colorfast wallpaper. When applying to a previously coated surface test in inconspicuous places for satisfactory appearance. Not for use on particle board or chipboard. APPLICATION - Always have adequate ventilation. Before using, mix coating thoroughly by gently stirring or rolling container to avoid air bubbles. Be sure to stir product thoroughly every 20 minutes during application. Do not shake container. Pour material to be used into another container before applying coating to avoid contaminating main container. Then apply as is, using a quality nylon brush, pad applicator, or unheated spray applicator. Apply liberal coats, keeping a good wet edge and avoid overbrushing. In most cases, a minimum of 2 coats is required, depending on the surface. When spraying, use a .015 tip or smaller. Apply thin even coats when spraying rather than heavy coats which will tend to sag. If spray pattern begins to dryspray, reduce air pressure and increase material flow to surface. Use a damp, dust free rag after sanding to remove dust particles. Use aluminum oxide or silicon carbide sandpaper to sand between coats. For best results, this product should not be reduced. Use only during low or moderate humidity conditions. Applying this product over lightly dampened surfaces can assist the user in controlling the dry time. Smoother finishes are achieved when surfaces are damp during application. For best results, this product should not be reduced. Note: these instructions are intended to be general only and not exhaustive. The applicator should determine what preparation and techniques are best suited to the specific surface. COVERAGE - One gallon of Safecoat Hard Seal covers approximately 350 square feet in one coat depending on surface porosity. DRYING/CURING TIME - Under normal conditions, Safecoat Hard Seal dries to touch in one hour and is re-coatable after 2 hours. Normal conditions include a dry surface, access to fresh air flow, moderate humidity, and temperatures above 55°F. Thick application, high humidity or conditions other than normal will cause Safecoat Hard Seal to dry and cure more slowly. SPEC SHEET $27.00 AFM Product Size *
	DuroTone - gallon ****SOME COLORS OUT OF STOCK DUE TO COVID MATERIAL SHORTAGES Safecoat DuroTone^TM is a fast curing low odor semi-transparent interior wood stain using no aromatic solvents, formaldehyde, UV inhibitors or Hazardous Air Pollutants. Available in Cognac, Walnut, Warm Cherry, Golden Oak, Honey Maple, Jacobean, Red Mahogany, Warm Oak, Nutmeg, Pecan, White Pickle and Clear. Available in pints or gallons. SPEC SHEET $39.00 DuroTone Color
	DuroStain Safecoat Stains & Sealers Using natural mineral pigments instead of dyes and no formaldehyde or other toxic ingredients, our extensive collection of stains and sealers gives you unprecedented versatility for coating a wide variety of surfaces with a strong, durable finish that has no offensive solvents, fumes or odors. Our stains offer superior coloration for any interior and exterior wooden surfaces. Our unique sealers offer superior protection and seal in harmful toxins on surfaces that include wood, concrete, natural stone, stucco and tile grout. DuroStain This premium quality, fast-curing flat finish, semi-transparent stain is ideal for interior and exterior wood surfaces. It promotes penetration of porous surfaces and has high adhesion for superior protection as a decorative colorant. It has excellent pigmentation stability and is a durable stain. It contains no aniline dyestuffs, no gilsonite or asphalt, no aromatic solvents and no formaldehyde. Use on: all wood surfaces. SCS CERTIFIED - LEED QUALIFIED SURFACE PREPARATION : Because of wide variations in the way different woods accept stain, we particularly recommend that users always test in small, inconspicuous areas for appearance and compatibility before application to the entire surface . Surfaces to be stained with Safecoat DuroStain should be sound and cleaned of dirt, dust, grease, wax, silicone, soap and oil, and must be completely free of mold, mildew or fungus contamination. Cleaning with an odorless, dye-free, all-purpose cleaner like SafeChoice Super Clean is recommended. Previously painted or sealed surfaces will not accept stain readily. Consequently, stripping of old paint or sealer followed by rinsing and sanding will be required before application of Safecoat DuroStain to achieve maximum penetration from this product. Surface can be dampened with water to assist user in getting an even application. Porous woods with strong grain pattern can be tamed by using thinned (50% with water) application of Safecoat® DuroStain Clear. Safecoat® DuroStain can be used as a glaze over painted and sealed surfaces. APPLICATION : Always have adequate ventilation. Intermix (boxing) all containers of the same color to ensure uniformity before applying. Before using, stir Safecoat DuroStain well, then apply it evenly without reduction using a high quality nylon or synthetic bristle brush. To adjust intensity of color, best results will be obtained by staining six foot sections (2’ x 3’) of the surface and wiping off excess stain while it is still wet to achieve the desired intensity of color. Always keep a wet edge. Darkness of stain may be increased by high surface porosity, wiping off less stain, or letting the stain dry longer before wiping. A squeegee applicator can be beneficial when coating large flat surfaces like doors. The shade of the stained surface will be affected by the color and type of wood. Reduce if desired for spraying with up to 1/2 pint of water per gallon. Always use a painter’s mask when spraying. Do not apply in direct sunlight. Make sure to wipe off any excess stain which does not penetrate into the wood. Note: these instructions are intended to be general only and not exhaustive. The applicator should determine what preparation and techniques are best suited to the specific surface SPEC SHEET $14.00 DuroStain color and size